Butterfly valves
What is a butterfly valve used for?
A butterfly valve isolates or regulates flow with a disc that turns a quarter turn. It is the common choice on water supply, cooling water, sewage and air lines from DN 50 upwards, because it is short, light and economical in large sizes.
What is the difference between wafer and lug type butterfly valves?
A wafer valve is clamped between two flanges by through-bolts; a lug valve has threaded lugs, so each flange bolts to it separately and the line can be opened on one side. See our wafer vs lug guide.
What is the difference between gear operated and lever operated butterfly valves?
A lever turns the disc directly and locks in notched positions; a gearbox multiplies the operator's effort and holds any position. Levers suit smaller sizes, roughly up to DN 200; gearboxes suit larger valves and higher pressures.
What does PN 16 mean on a butterfly valve?
PN 16 means a nominal pressure of 16 bar at 20 °C. It also tells you which flange drilling the valve is made to match. See PN 10 vs PN 16.
Do you supply butterfly valves made to IS 13095?
Yes. Valvetech, the Ezzi group's own brand, builds butterfly valves to IS 13095. See Valvetech.
Channel drains
What is load class EN 1433?
EN 1433 is the European standard for drainage channels in vehicle and pedestrian areas. It sets six load classes, from A 15 for pedestrian areas to F 900 for very heavy wheel loads such as airports and docks. The number is the test load in kilonewtons.
Which load class do I need for a driveway or car park?
B 125 suits footpaths and car parks used by cars. Where lorries or all vehicle types drive and park, choose D 400. Docks, container yards and airport aprons need E 600 or F 900.
Is a trench drain the same as a channel drain?
Yes. Trench drain, channel drain, line drain and storm water drain channel are names for the same thing: a channel with a grating that drains a surface along a line.
Why choose polymer concrete over a cast-in-situ concrete drain?
Polymer concrete channels are made to size in the factory, have a smooth surface that sheds silt, are light to lay, and resist chemicals and frost. A cast-in-situ drain depends on the site's formwork and finish.
Valves
What are the main types of industrial valves and their uses?
Butterfly, gate and ball valves isolate a line; globe valves throttle it; check valves stop reverse flow; actuated valves do any of these on a control signal.
Which valve is used to prevent backflow?
A check valve, called a non-return valve or NRV in India. It is fitted on pump discharge lines, before the isolation valve, so the column of water cannot run back through the pump.
Which valve is used for throttling?
A globe valve is the usual choice, because its plug closes square to the seat and regulates finely. Butterfly valves also throttle, within the opening range their maker states.
Which valve is used on a steam line?
Globe valves for regulation and gate valves for isolation, in cast or forged steel with a rating that covers the steam's pressure and temperature.
Can I get several valve types in one quotation?
Yes. Send your BOQ, drawing or list of sizes through Request a quote or to sales@ezzihardware.com, and we price the complete line together.
Ball valves
What is the difference between a 2-piece and a 3-piece ball valve?
A 3-piece ball valve has a centre body held between two end pieces, so the ball and seats can be replaced without cutting it out of the line. A 2-piece valve is cheaper but must come out of the line for service.
Ball valve or butterfly valve: which is better?
For small bores and a tight, quick shut-off, a ball valve; for large bores on water and air, a butterfly valve, which is lighter and more economical. See butterfly vs gate vs ball.
Which ball valve is used for chemicals?
Stainless steel ball valves with PTFE seats for most solvents and mild chemicals, and uPVC, PP or PVDF ball valves for acids and alkalis. Send the chemical and temperature and we confirm compatibility.
Building drainage
Why use a stainless steel floor drain in a commercial kitchen?
Stainless steel resists hot water, cleaning chemicals and food acids, has no pores for bacteria, and does not rust. ACO's hygienic gullies and channels are also shaped so waste cannot collect in corners.
What do load classes K3 and L15 mean for a floor drain?
They are EN 1253 load classes for floor drains. K3 is for areas without vehicle traffic, such as bathrooms and showers. L15 is for areas with light vehicle traffic, excluding forklifts, such as commercial kitchens.
What is the difference between a linear shower channel and a point drain?
A linear shower channel runs along one edge of the shower, so the floor falls one way and large tiles can be used. A point drain sits in the floor and the floor falls to it from all sides.
CPVC & uPVC
CPVC or uPVC: which is better?
Neither is better everywhere: CPVC carries hot water, uPVC is for cold water, drainage and many chemicals at ambient temperature. See CPVC vs uPVC.
What is SDR 11 in CPVC pipe?
SDR is the ratio of outside diameter to wall thickness. SDR 11 has a thicker wall than SDR 13.5 at the same size, so it carries a higher pressure.
What is the difference between Schedule 40 and Schedule 80 pipe?
At the same size, both have the same outside diameter, but Schedule 80 has a thicker wall, a smaller bore and a higher pressure rating. Industrial chemical lines usually use Schedule 80.
Can CPVC pipe be exposed to sunlight?
Follow the maker's guidance for the grade: many CPVC pipes are UV-stabilised for some exposure, but long outdoor runs are usually painted or protected.
DWC pipes
What is DWC pipe used for?
DWC (double wall corrugated) pipe is used for sewerage and storm drainage, and in a separate grade as a duct for underground power and telecom cables.
What does SN mean in DWC pipe?
SN is the nominal ring stiffness class, in kN/m². SN 8 is twice as stiff as SN 4 and is used under deeper cover or heavier traffic. See DWC pipe sizes, SN 4 vs SN 8.
What is the difference between DWC and HDPE pipe?
DWC is usually made of HDPE, but with a structured, corrugated outer wall; a plain HDPE pressure pipe has a solid wall. DWC is for gravity drainage and ducts, not for pressure mains.
What is the IS code for DWC sewer pipe?
IS 16098 (Part 2) covers structured-wall polyethylene pipes with a smooth inside and corrugated outside for non-pressure underground drainage and sewerage.
Gate and sluice valves
What is the difference between a sluice valve and a gate valve?
They are the same kind of valve: a wedge lifts clear of the bore. In India, a gate valve for water works is called a sluice valve and is made to IS 14846. See sluice vs gate.
What is a sluice valve used for?
Isolating water supply mains, pumping stations and sewage lines, where the valve stays fully open or fully shut and the bore must be clear.
What is the IS code for sluice valves?
IS 14846:2000, Sluice valve for water works purposes (50 to 1200 mm size). It replaced IS 780 and IS 2906.
Should I choose a CI or a DI sluice valve?
Ductile iron is tougher and less brittle than cast iron, so it is often specified for higher pressures, buried mains and lines exposed to shock. Follow the material your specification names.
Grease separators
What is a grease trap and why does a commercial kitchen need one?
A grease trap holds kitchen wastewater long enough for fats and oils to float and food solids to settle, so they are kept out of the drain. Without one, grease cools and blocks the pipes and the sewer.
What size grease trap do I need?
It depends on the flow from the sinks, dishwashers and other fittings connected. A single sink line suits an under-sink trap such as the ACO GT40; a hotel or food plant needs a separator sized to EN 1825 in nominal sizes (NS). Send us the fitting list and we size it.
What is the difference between a grease trap and a grease separator?
A grease trap is a small unit for one sink or a small kitchen. A grease separator is a larger tank, sized to EN 1825, with a sludge trap and grease store, for a whole kitchen or food plant.
How often should a grease separator be emptied?
When the grease layer and sludge reach the levels in the maker's instructions, and at the intervals your local authority sets. Automatic ACO units such as the LipuJet-P-OA clean themselves between emptyings.
Globe valves
What is the function of a globe valve?
A globe valve regulates flow. Its plug moves square to the seat, so it throttles finely and shuts tight, at the cost of a higher pressure drop than a gate valve.
Globe valve or gate valve for a steam line?
A globe valve where the steam must be regulated, a gate valve where the line is only opened or shut. Many steam lines carry both.
What is a Y-type globe valve?
A globe valve whose seat sits at an angle to the line, which gives a straighter flow path and a lower pressure drop than a straight-pattern globe valve.
Insulation
What is the best insulation for chilled water pipes?
Closed-cell nitrile rubber is the common choice, because it resists water vapour and so keeps condensation off the pipe; PUF sections are used on larger lines and cold stores.
What is the difference between hot and cold insulation?
Hot insulation keeps heat in and protects people from hot surfaces; cold insulation keeps heat out and, above all, stops condensation, so it needs a vapour barrier.
How thick should chilled water pipe insulation be?
It depends on the pipe size, the water temperature and the site's humidity. Send those three and we propose a thickness, or follow the thickness your HVAC consultant has specified.
Oil separators
What is an oil water separator?
A tank that lets oil-contaminated water stand long enough for the oil to rise and be held back, so only water goes to the drain. Class I separators to EN 858 use a coalescence insert to catch fine droplets.
Where is an oil separator required?
Wherever runoff can carry fuel or oil: petrol stations, workshops, car washes, bus and truck depots, car parks and generator areas. Check the requirement with your pollution control board consent.
What is the difference between Class I and Class II oil separators?
Under EN 858, a Class I separator leaves no more than 5 mg/l of oil in the outflow, using a coalescence insert. Class II allows up to 100 mg/l. The ACO separators listed here are Class I.
Check valves (NRV)
What is an NRV valve?
NRV stands for non-return valve, the Indian trade name for a check valve. It lets flow pass one way and closes when the flow reverses.
What is a dual plate check valve?
A check valve with two spring-loaded half discs on a central hinge pin. It is short, light and closes quickly, which reduces water hammer on pump discharge lines.
Dual plate or swing check valve?
Dual plate where space, weight and fast closing matter, as on most pump discharges; swing check where the line carries solids or needs a full, clear bore, as on many sewage lines.
Where is the NRV fitted on a pump line?
On the discharge side, between the pump and the isolation valve, so the isolation valve can be closed to service the NRV.
Expansion joints
What is a rubber bellow?
A rubber bellow, or rubber expansion joint, is a flexible flanged joint of reinforced rubber that absorbs movement, vibration and noise between a pump or machine and its pipework.
Why are expansion joints used in piping?
To take thermal expansion, vibration and small misalignments, so the movement does not stress the flanges, the pipe supports or the pump casing.
Rubber or metallic expansion joint?
Rubber for water, sewage and pump connections at moderate temperatures; metallic, with stainless steel bellows, for steam, hot oil and high temperatures. See rubber vs metallic.
Lifting stations
What is a sewage lifting station?
A tank with a pump that collects wastewater from fixtures below the sewer level, such as a basement toilet, and pumps it up into the sewer.
Do I need a faeces lifting plant or a grey water pump?
A grey water lifting plant suits showers, washbasins and laundries. Any toilet connected needs a plant for wastewater containing faeces, such as the Muli-Star DDP or Muli-Nova DDP.
Actuated valves
What does actuated valve mean?
A valve fitted with an actuator, a pneumatic or electric drive that opens and closes it from a signal instead of by hand.
Pneumatic or electric actuator: which should I choose?
Pneumatic where the plant has compressed air and needs fast or fail-safe operation; electric where there is no air supply or the valve is remote. Both can be on-off or modulating.
What is the difference between double acting and spring return actuators?
A double acting actuator uses air to open and to close; a spring return actuator uses air one way and a spring the other, so the valve moves to a safe position if air or power fails.
What is ISO 5211?
The international standard for the mounting flange and drive between a quarter-turn valve and its actuator, so a valve and an actuator from different makers can be fitted together.
Camlock couplings
What is a camlock coupling?
A quick-release hose coupling: a grooved male adapter locks into a female coupler when two cam arms are folded down, with a gasket sealing the joint.
What are the camlock coupling types?
Types A, B, C, D, E and F, plus dust caps and dust plugs. A, E, F and the dust plug are male adapters; B, C, D and the dust cap are female couplers. See the camlock types chart.
Which camlock types fit each other?
Any male adapter fits any female coupler of the same size, whatever the letter. The letter only describes the other end: thread, hose shank or plug.
Which camlock material should I choose?
SS 316 for chemicals and food, SS 304 for general service, aluminium for fuel tankers, brass for water and oil, PP for acids. Choose the gasket for the product too.
Stormwater storage
What is a stormwater attenuation tank?
An underground tank that holds back stormwater during heavy rain and releases it slowly, so drains and streams downstream do not flood.
Can Stormbrixx be used for rainwater harvesting?
Yes. Stormbrixx can be built as a tank for retention and reuse, or as a soakaway that recharges the ground.
Drainage
What is the difference between a channel drain and a floor gully?
A channel drain is a long, narrow channel with a grating that collects water along a line, such as a driveway edge or loading bay. A floor gully collects water at one point, such as a kitchen or bathroom floor.
Do you supply ACO drainage outside Chennai?
Yes. Our ACO dealership covers all of India. Tell us the site location with your enquiry and we quote supply and delivery to it.
What do you need to quote a drainage job?
The drawing or BOQ, the area to be drained, the traffic that will cross it, and for separators the fittings or flow connected. We confirm the ACO product and size from that.
Questions
What is the PN 16 pressure rating?
PN 16 is a nominal pressure of 16 bar at 20 °C, about 232 psi. The allowed pressure falls as temperature rises.
What is the full form of DWC pipe?
Double wall corrugated pipe.
What is the full form of NRV?
Non-return valve: a check valve that lets flow pass one way only.
What is an EPDM seat?
A valve seat of EPDM rubber, the usual choice for water, which resists hot water and weather but not oils or fuels.
What is a double eccentric butterfly valve?
A butterfly valve whose shaft is offset from both the centre of the disc and the centre of the bore, so the disc lifts off the seat as it opens. It seals better and wears less than a concentric valve, and suits higher pressures.
How do I convert DN to inches?
DN 15 is ½ inch, DN 25 is 1 inch, DN 50 is 2 inches, DN 100 is 4 inches and DN 150 is 6 inches. See the full DN to inch chart.
Do you supply to EPC contractors and government projects?
Yes. We quote to specifications and vendor lists, and supply the test certificates and inspection documents projects require.
A size or rating not listed?
Our procurement desk sources it, from Valvetech or anywhere in the world.